EFJohnson Viking Ranger Upgrade Kit

Description: Our direct email links are here: http://members.ebay.com/ws/eBayISAPI.dll?ViewUserPage&userid=cornelius_connie www.kiss-electronics.com For Auction: * EF Johnson Viking Ranger Upgrade Kit: Upgrade kit consists of: *(1) Solid State "Drive" control assembly, * (1)Solid State +300V regulator assembly. * (1) + 150V regulator assembly. * (1), LV Filter capacitor (typically either 50uf/450, or 100uf/450VDC) * (1) solid state plug in LV replacement rectifier assembly [ 2kvprv/1Amp ] for the 6AX5 * (1) VFO Alignment tool. * NOTE: Each of these modules may be purchased separately, ebay messaging to us for details * The solid state +300V regulator assembly is compatible with the Johnson Viking I & II, Johnson Valiant, as well as the Johnson Ranger. * The Solid State VFO +150V regulator is a replacement for the 18K resistor/VR tube scheme in the Johnson VFO, this assembly is usable with the VFO 122, as well as any Johnson Transmitter that uses their "standard" VFO). The Solid State "Drive" control assembly is usable ( with a slight modification ie: moving the Drive potentiometer to the front panel to replace the original Drive control) also with the Viking I & II and Johnson Valiant. * The Solid State Drive Control assembly replaces the 25K "Drive" potentiometer, (a high failure rate item because it also acts as the 300VDC power supply bleeder resistor). * Operation of the Solid State Drive unit is very smooth and reliable. LV Bleeder current is reduced to a low value and thus heat generated is also reduced. The potentiometer used in the "Drive unit" is an Allen Bradley,Centralab or similiar high quality unit. * The control element in both the +300V regulator and the Drive Unit is a high current power FET. The Solid State +300VDC regulator assembly tames the low voltage Buss to +300VDC. **[ Sidebar: When the +300V regulator assembly is installed, the Modulator Tube Screens may be connected directly to the +300V regulated buss, and the HV bleeder resistor removed ( replace with 2 X 470K/2w resistors, NOT included in this kit). IF you accomplish this, the original Modulator Fixed Bias circuit will need to be modified to allow for an adjustable bias voltage ( Email for details of this modification). * The Solid state 300VDC regulator assembly has been tested with DC inputs up to +375VDC or so.( Higher input voltages may require modification of the values of the shunt resistors ( See Schematic). The Solid State VFO Regulator assembly allows you to remove the VFO dropping resistor and regulator tube ( both high failure items). ( VFO Shroud removal necessary to install the VFO Solid State Regulator assembly) . The solid state plug in 6AX5 assembly directly replaces the vacuum tube LV rectifier 6AX5 with no circuit modifications. The parts used in these assemblies are new, rated for far more voltage and current than will ever be encountered in the Ranger .***** Installation suggestions and schematic packages are sent via Email to the buyer, after sale.****** * We have tested these assemblies in our shop before shipment. Resistor values on each of these assemblies may be altered for other B+ voltages. We have tested the Drive , VFO regulator , solid state 6AX5 and 300VDC assemblies in our shop. These control assemblies and the alignment tool are hand made, therefore each is slightly different,depending on the potentiometer and other parts available. Installation of these assemblies does take a bit of technical expertise and patience. * The VFO Alignment Tool allows you to accomplish a VFO periodic alignment even if, as is often the case, the original "alignment shaft spring assemblies" are missing or broken. We DO recommend when you overhaul your Ranger, you remove the original VFO "alignment pins" and discard them. Open holes in the VFO shroud may be plugged with appropriate metal or plastic hole plugs. ( NOT SUPPLIED). * Shipping is USPS Priority Mail Flat Rate insured. *** NO international shipping !! *** * All sales are final: No warranties, or guarantees expressed or implied. No returns. We will work with you if you have problems with the installation. * Pricing for this package is less than the individual items purchased separately. *****POTENTIALLY LETHAL HIGH VOLTAGES ARE INVOLVED IN THE INSTALLATION OF THESE PRODUCTS, PLEASE BE SURE TO OBSERVE ALL SAFETY PRECAUTIONS ***** These assemblies are designed to reduce heat issues with the Johnson Ranger, as well as increase the reliability ( especially the "Drive" control) of the unit. Photos: ** Stock Photo: *** NOTE*** Two of the photos show typical Ranger Installation configuration for (1) Lower Left: Solid State Drive Module, (2) Center of photo, just below band switch shield, typical installation configuration for the +300V solid state regulator module. Be aware that the LV filter choke in the Ranger is a 10H unit and for the solid state 300V regulator module to function properly, this choke value must remain 10H. ***** Kiss-Electronics.com QRZ: W7DUZ Thank You Kiss Electronics Our direct email links are here: http://members.ebay.com/ws/eBayISAPI.dll?ViewUserPage&userid=cornelius_connie www.kiss-electronics.com

Price: 120 USD

Location: Cornelius, Oregon

End Time: 2024-11-15T07:17:05.000Z

Shipping Cost: 19.3 USD